Skip to content
+40 371 232 404|Mon - Fri: 08:00 - 16:30 (Romania time)

Wago supplier in Romania

For Wago we quote PFC200 controllers from the 750 series (for example 750-8202 and 750-8210), fieldbus I/O modules, TOPJOB S spring terminal blocks and interface relays; we quote by code, including for SEAP tenders.

Founded in 1951 · Headquarters: Minden, Germany

Request a quote

Who is Wago and what does it make?

Wago is the inventor of spring clamp terminal blocks and a manufacturer active worldwide in screwless electrical connection technology. Classic screw terminal blocks can loosen over time, especially with aluminium cables or many thermal cycles; Wago TOPJOB S offers an alternative — insert the cable, press the orange lever, done. No tools, no screws to tighten. The company started in 1951 and launched its first spring terminal block in 1977 — since then, its technology has become widespread in industry, from simple control cabinets to complex offshore installations or airports.

On installations that use Wago connections instead of classic terminal blocks, the difference lies in reduced wiring time, fewer tightening errors (damaged cable or poor contact) and long-term reliability with low maintenance. On installations with aluminium cables (used more and more often to save cost), this type of connection is recommended — the spring keeps constant pressure even when the aluminium "flows" over time (a relaxation phenomenon). Testing circuits is simple — lift the orange lever, insert a tester, check the voltage, close the lever — all without disconnecting the cable.

But Wago is not only terminal blocks — it has developed a range of industrial automation products based on the same philosophy of fast and secure connection. I/O modules for fieldbus (Profinet, EtherNet/IP, Modbus), compact 750 series PLCs, interface relays, and complete energy management systems.

What do we supply from the Wago range?

ProductDescription
TOPJOB S Spring Clamp Terminal BlocksThe TOPJOB S family is widely used for fast and secure connections — CAGE CLAMP spring terminal blocks that accept rigid and flexible cables; the cross-section range depends on the code and we confirm it from the manufacturer's datasheet. DIN 35mm rail mounting, and the option of jumpering (multiple connection between terminal blocks) through dedicated bars. Also includes PE (earth) protective terminal blocks with green-yellow visual coding, disconnect terminal blocks with integrated fuses, and multi-level terminal blocks with up to 4 connection levels in the same position (saving space in small cabinets). Data on pull-out strength, vibration resistance and contact material are confirmed from the manufacturer's datasheet for the chosen code.
Fieldbus I/O Modules (750 Series)Modular I/O systems for connecting sensors and actuators to industrial networks — Profinet, EtherNet/IP, Modbus TCP/RTU, CANopen, DeviceNet, and others. Each system starts with a controller/coupler that interfaces to the bus, and then you add I/O modules as needed — digital (8/16 DI/DO channels), analogue (2/4/8 AI/AO channels, 4-20mA, 0-10V, thermocouples, RTD), and special (fast counters, SSI encoders, step/direction for stepper motors). DIN rail mounting, internal connection through an integrated bus (no wiring between modules). Free Wago-I/O-Check software for configuration and diagnostics. Ideal for retrofit or for applications where centralised I/O is not feasible.
Compact PLC 750 Series (Controller)Compact PLCs programmable in CODESYS V3 (IEC 61131-3 languages: Ladder, FBD, ST, SFC) with integrated modular I/O — up to 250 I/O modules on one node. Includes Ethernet ports for Modbus TCP, HMI integration, and remote access, plus serial ports for Modbus RTU and legacy devices. Memory depends on the model: for example, 750-8208 has 16 MB of program memory and 64 MB of data memory (CODESYS V2), and 750-8210 accepts an SD/SDHC card. Suited to applications where a large classic PLC would be oversized — small and medium machines, mobile machinery, decentralised installations. CODESYS software is free, with extensive libraries for PID control, motion, communications, and HMI.
Interface Relays and Safety ModulesInterface relays (relay couplers) for isolation between the PLC and power loads — 24VDC coils with 250VAC/6A contacts for controlling contactors, solenoid valves, alarms. Available single (1 contact), double (2 contacts), and with a status LED for visual diagnostics. Also includes functional safety modules for safety functions — monitoring of emergency stop buttons, safety gates, safety mats, light curtains, with safe outputs for the controlled stopping of machines. DIN rail mounting next to TOPJOB S terminal blocks for uniform and neat wiring.

Why Wago?

  • Spring connection — patented CAGE CLAMP technology for a secure screwless connection
  • Fast connection — quicker installation than with classic screw terminal blocks
  • Vibration resistance — the spring keeps constant pressure even on machines with continuous shocks and vibration
  • Suitable for aluminium — a recommended solution for aluminium cables, which tend to deform over time
  • Range from simple terminal blocks to complex automation systems and remote I/O
  • Certifications and approvals according to the manufacturer's documentation

Which Wago codes and series are requested most often?

CodeDescription
750-8202PFC200 controller with Ethernet and RS-232/RS-485 interface
750-8210PFC200 second-generation controller, 4 x Ethernet
750-8208PFC200 controller with 2 x Ethernet, RS-232/RS-485, CAN/CANopen and PROFIBUS DP Master
750-8212PFC200 second-generation controller, 2x Ethernet, RS-232/RS-485
750-8216/025-001PFC200 controller, version with specific firmware configuration
750-8202/025-002PFC200 controller, version with customised software configuration
750-8212/040-010PFC200 second-generation controller, customised configuration
750-8202/000-012PFC200 controller, FG2 version, 2 x Ethernet, RS-232/RS-485
2002-2201TOPJOB S two-level terminal block, rail mounting, grey
2002-2202TOPJOB S two-level terminal block, rail mounting, grey; differences from 2002-2201 are confirmed from the manufacturer's datasheet

Where is Wago equipment used?

  • Electrical panels — power distribution, motor control, automation
  • Automotive — assembly lines, robotics, test stations
  • Food and beverage — wash-down resistant connections, I/O modules for PLCs
  • Pharmaceutical and chemical — ATEX zones, controllers for batch processes
  • Energy — thermal power plants, photovoltaic, wind, energy management systems
  • Naval and offshore — panels for saline environments, vibration
  • Smart buildings — HVAC automation, lighting, access control
  • Rail transport — wiring for trains and trams, vibration resistance
  • Mining — mobile machinery, shock- and dust-resistant connections
  • Machine building — machine tools, packaging, textile, print

How do we supply Wago in Romania?

For Wago, we work from what we confirm on each order and from the manufacturer's technical documentation. Wago products reach us to order, with references that can ship in 24–72 h when the item is in stock, locally or at the supplier, and usually 1–4 weeks to order for the rest of the range or project configurations. For a correct quotation, send the cable cross-section or the terminal block code, the bus protocol used (Profinet, EtherNet/IP, Modbus), the number of channels needed and the quantity. For safety modules or 750 series PLCs we recommend a technical check before a lead time is confirmed.

Programming or configuring 750 series PLCs in CODESYS is outside our offer, and availability of I/O modules is confirmed in the quotation, for each code.

Frequently asked questions about Wago

Which WAGO PFC200 controller should I choose for automation with two separate Ethernet networks?

The 750-8212 model, second generation, has two Ethernet ports and an RS-232/RS-485 serial interface, suited to separating the process network from the supervision network. For additional firmware or software requirements, customised versions such as 750-8212/040-010 cover specific project configurations.

What is the difference between the WAGO TOPJOB S terminal blocks 2002-2201 and 2002-2202?

Both are two-level terminal blocks from the TOPJOB S series, rail-mounted, with the same width of 5.2 mm and grey colour. The differences between the two codes (level configuration and marking) are confirmed from the manufacturer's datasheet before ordering.

Do you supply WAGO equipment in Romania?

Yes, we bring in WAGO controllers and terminal blocks to order, based on the product datasheets published by the manufacturer; the lead time and availability are given in the quotation. The lead time to order for Wago is usually 1–4 weeks, depending on the model and quantity. We recommend confirming the exact code, including configuration suffixes, before ordering.

What information should I send for a WAGO PFC200 controller quotation?

The number and type of communication interfaces needed, the automation protocol used, and whether a customised firmware configuration is required are all useful. These details make it possible to choose between a base model, such as 750-8202, or a project-specific customised version.

What is the WAGO TOPJOB S series of spring terminal blocks?

It is a range of spring connection terminal blocks, rail-mounted, designed for quick connection of the conductor without special tightening tools. Multi-level versions, such as 2002-2201 (two levels), take up less space in the electrical panel than single-level terminal blocks for the same number of circuits.

How do I request a Wago quotation?

Send the Wago code from the nameplate and the quantity; we reply in English with availability and the lead time written in the quotation.

Request a quote

Updated: 21 November 2026 · Sources: Wago, WAGO GmbH & Co. KG (manufacturer documentation)