Skip to content
+40 371 232 404|Mon - Fri: 08:00 - 16:30 (Romania time)

Pentax (pompe) supplier in Romania

For Pentax we quote CM and CS centrifugal pumps, CA standardised pumps, ULTRA multistage pumps, 4L and 6S submersible pumps and VP vertical pumps; we need the type on the nameplate, the motor power and the duty point.

Headquarters: Veronella, Italy

Request a quote

Who is Pentax (pompe) and what does it make?

Pentax is an Italian pump manufacturer from Veronella, in the province of Verona: close-coupled centrifugal pumps, EN 733 standardised pumps, vertical multistage stainless steel pumps, submersible pumps for 4" and 6" wells and long-shaft vertical pumps for high flows. The pumps work in water supply, pressure boosting, irrigation, firefighting, heating and air conditioning and in industry. For a quotation, send us the full type from the nameplate, for example CM50-160 or ULTRA, and the duty point.

The CM series has a single impeller, a cast iron casing and a Noryl or brass impeller, liquid up to 90 °C with the brass impeller and working pressure of up to 8 bar on the large sizes. The CS series also has a single impeller, but gives medium and large flows on 2", 3" and 4" connections, especially for agriculture. CA, CAT and CAX pumps are built to EN 733 and run at about 2,900 rpm. ULTRA SLG and SLXG vertical multistage pumps have impellers, diffusers and shaft in AISI 304 steel, work with liquids between −15 and +110 °C and withstand up to 25 bar, in pressure boosting sets, water treatment, glycol water and the food industry.

4L and 6S submersible pumps are multistage, have a check valve built into the discharge and a motor coupling flange to the NEMA standard. The VP line, with vertical pumps, reaches flows of 1,600 m³/h and heads of 400 m and is used in firefighting installations, petrochemicals, mining and power plants, with an electric motor or, through an angular gearbox, with a combustion engine. Each VP pump goes through end-of-line tests, and the hydraulic performance is checked to ISO 9906, grade 2B.

What do we supply from the Pentax (pompe) range?

ProductDescription
CMClose-coupled centrifugal pumps with a single impeller, with cast iron casing, Noryl or brass impeller and ceramic–graphite mechanical seal. They work with clean liquid up to 90 °C with the brass impeller and up to 6–8 bar, in water supply, pressure boosting and civil and industrial applications, with a flat pressure curve.
ULTRA SLG / SLXGVertical multistage centrifugal pumps, with impellers, diffusers, sleeve and shaft in AISI 304 steel; on the SLXG the pump casing is also stainless steel. Liquid between −15 and +110 °C, pressure of up to 25 bar, IP55 motor, for pressure boosting, irrigation, glycol water, water treatment and the food industry.
4L / 6SMultistage submersible pumps for 4" and 6" wells, with a check valve built into the discharge and a motor coupling flange to NEMA. On the 6S, the motor can be encapsulated or rewindable, in an oil bath. They are used mainly in water supply and in agriculture.
VP lineLong-shaft vertical pumps, for flows of up to 1,600 m³/h and heads of up to 400 m, with hydraulic efficiency of up to 82 %. They are driven by an electric motor or, through an angular gearbox or belt, by a combustion engine, for firefighting, petrochemicals, mining and power plants.

Why Pentax (pompe)?

  • A range from close-coupled to vertical pumps — CM, CS and CA cover water transfer, while the VP line reaches 1,600 m³/h and 400 m
  • Stainless steel in multistage pumps — ULTRA SLG and SLXG have AISI 304 hydraulic parts, liquid between −15 and +110 °C and up to 25 bar
  • Standardised pumps — the CA, CAT and CAX series are built to EN 733
  • 4" and 6" wells — 4L and 6S submersible pumps have a built-in check valve and NEMA motor coupling
  • End-of-line testing — VP pumps are checked hydraulically to ISO 9906 grade 2B

Which Pentax (pompe) codes and series are requested most often?

CodeDescription
CMClose-coupled centrifugal pumps with a single impeller
CM50-160CM series close-coupled centrifugal pump, EN 733, about 2,900 rpm
CSSingle-impeller centrifugal pumps, medium and large flows, 2"–4" connections
CA 32-250EN 733 centrifugal pump, 2,900 rpm
CATEN 733 standardised centrifugal pumps
ULTRA SLGVertical multistage pumps with AISI 304 hydraulic parts
ULTRA SLXGVertical multistage pumps with stainless steel casing
4LMultistage submersible pumps for 4" wells
6SMultistage submersible pumps for 6" wells
VPLong-shaft vertical pumps, up to 1,600 m³/h

Where is Pentax (pompe) equipment used?

  • Water supply and pressure boosting — CM pumps and ULTRA multistage pumps in pumping sets
  • Agriculture and irrigation — CS pumps and 4L and 6S submersible pumps for wells
  • Fire protection — VP vertical pumps driven electrically or by a combustion engine
  • Petrochemicals, mining and power plants — long-shaft VP pumps for high flows
  • Heating, air conditioning and water treatment — stainless steel ULTRA pumps for glycol water

How do we supply Pentax (pompe) in Romania?

We can quote Pentax CM, CS and CA/CAT/CAX pumps, ULTRA multistage pumps, 4L and 6S submersible pumps and VP line vertical pumps, plus mechanical seals and replacement impellers. For an accurate quotation, send us the full type from the pump nameplate, the motor power and voltage, the pumped liquid and its temperature and, for new pumps, the flow and head required. Pentax pumps are brought in from Italy to order, usually with a lead time of 1–4 weeks; a pump can ship in 24–72 h when the item is in stock, locally or at the supplier, and for VP pumps, depending on the specification, the lead time may be longer.

Pentax pumps from these series are for clean, unloaded water and liquids; for liquids with solids or chemically aggressive ones we propose other designs, based on the process data.

Frequently asked questions about Pentax (pompe)

What pumps does Pentax make?

Pentax makes CM and CS close-coupled centrifugal pumps, EN 733 standardised pumps of the CA, CAT and CAX series, ULTRA multistage pumps, 4L and 6S submersible pumps for wells and long-shaft vertical pumps from the VP line, with flows of up to 1,600 m³/h. The company is based in Veronella, Italy.

How do I choose between a Pentax CM pump and an ULTRA multistage?

CM has a single impeller and suits higher flows with moderate heads, up to 6–8 bar. ULTRA SLG and SLXG have several AISI 304 stages and go up to 25 bar, so they are for pressure boosting and glycol water. Send us the flow, the head and the liquid temperature.

What is the lead time for a Pentax pump?

Supplied to order, Pentax pumps arrive from Italy usually in 1–4 weeks; a pump can ship in 24–72 h when the item is in stock, locally or at the supplier. For VP vertical pumps, depending on the specification, the lead time may be longer.

I have an old Pentax pump; can you find the impeller and seal?

Usually yes, if we know the exact pump type. Send us the code on the nameplate, for example CM50-160 or the full code of an ULTRA pump, the approximate year, the impeller material (Noryl, brass or cast iron) and the shaft diameter at the mechanical seal. With these we identify the parts from the list of the series concerned.

What do I send for a quotation on a Pentax 4L or 6S submersible pump?

We need the well diameter, the dynamic water level, the installation depth, the flow and head required, the available voltage and the amount of sand in the water. If you are replacing an existing pump, the code on the pump and motor nameplate is enough for a quotation.

How do I request a Pentax (pompe) quotation?

Send the Pentax (pompe) code from the nameplate and the quantity; we reply in English with availability and the lead time written in the quotation.

Request a quote

Updated: 20 November 2026 · Sources: Pentax Industries (manufacturer documentation)