Skip to content
+40 371 232 404|Mon - Fri: 08:00 - 16:30 (Romania time)

Electrolube supplier in Romania

For Electrolube we quote UVFlex and DCA protective coatings, the ER2074 encapsulation resin, HTS, HTSP, HTC and HTCP thermal pastes, PCG gels, LGF gap fillers and GFP pads; we need the application, the temperature and the application method.

Request a quote

Who is Electrolube and what does it make?

Electrolube makes chemicals for electronics: protective coatings for boards with components, casting and encapsulation resins and thermal interface materials. The range is chosen according to the problem it solves: protecting the board against environmental factors, fixing and insulating an assembly, or transferring heat from a component to a heat sink.

Among the protective coatings, UVFlex is a single-component, UV-cured coating, free of solvents, PFAS and silicone, resistant to more than 1,000 thermal cycles between −40 and +125 °C, with a working temperature from −40 to +150 °C. DCA is a modified alkyd coating, transparent and flexible, applied by spraying, from the can or from an aerosol, by immersion or with a brush, and it can be reworked with a special removal product.

ER2074 epoxy resin, with two components, is flame retardant and thermally conductive, with a working temperature from −40 to +130 °C and a UL94 V-0 flammability rating. The HTS, HTSP, HTC and HTCP thermal pastes do not cure (non-curing), and HTC and HTCP are silicone-free. The PCG300 and PCG400 gels, the two-component LGF gap fillers and the GFP pads complete the range for thermal gaps.

For a correct quotation, what matters is the application, the working temperature and the application method: the coating, the resin and the thermal paste solve different problems, and switching between silicone and silicone-free variants is checked against the application.

What do we supply from the Electrolube range?

ProductDescription
Protective coatingsUVFlex, a single-component, UV-cured, solvent-free coating, resistant to more than 1,000 thermal cycles between −40 and +125 °C, and DCA, a modified alkyd coating, applicable by spraying, immersion or brush, which can be reworked with a special product.
Casting and encapsulation resinsER2074 is a two-component epoxy resin, flame retardant and thermally conductive (1.26 W/m·K), with a working temperature between −40 and +130 °C. It is used to encapsulate circuits that must dissipate heat, for example those for LEDs.
Thermal pastesHTS and HTSP contain silicone, HTC and HTCP are silicone-free; all are pastes that do not cure and need no mixing. HTCP has a thermal conductivity of 2.5 W/m·K, and HTSP 3.0 W/m·K. The PCG300 and PCG400 gels complete the range.
Gap fillers and padsLGF200, LGF400 and LGF600 are two-component gap fillers, with a 1:1 mix ratio, which cure in place. The GFP pads are 0.5–5 mm thick, and the TDS100P dielectric sheets are 0.15 mm.

Why Electrolube?

  • UVFlex, UV-cured, free of solvents, PFAS and silicone — fast processing and resistance to more than 1,000 thermal cycles
  • DCA coating, applicable by spraying, immersion, aerosol or brush — it suits both automatic lines and touch-ups
  • ER2074 resin, flame retardant (UL94 V-0) and thermally conductive — protection of LED circuits and of modules that heat up
  • Thermal pastes with and without silicone — HTCP is recommended where silicones are prohibited
  • Gels, gap fillers and pads of 0.5–5 mm — gaps of different heights are covered by the same family

Which Electrolube codes and series are requested most often?

CodeDescription
UVFlexUV-cured protective coating, single component
DCAModified alkyd protective coating
ER2074Epoxy encapsulation resin, flame retardant, thermally conductive
HTSThermal paste with silicone
HTSPThermal paste with silicone, 3.0 W/m·K
HTCSilicone-free thermal paste
HTCPSilicone-free thermal paste, 2.5 W/m·K
PCG300Pre-cured thermal gel, 3.0 W/m·K
PCG400Pre-cured thermal gel, 4.0 W/m·K
LGF200Two-component liquid gap filler, 2.0 W/m·K
LGF400Two-component liquid gap filler, 4.0 W/m·K
LGF600Two-component liquid gap filler, 6.0 W/m·K
GFP300Thermal gap pad, 3.0 W/m·K
TDS100PDielectric sheet with polyimide

Where is Electrolube equipment used?

  • Power electronics — thermally conductive resins and interface materials for modules
  • LED lighting — encapsulation with ER2074 and thermal paste
  • Electronic board production — protective coatings applied by spraying or immersion
  • Industrial electronics — boards exposed to temperature variations and to solvents
  • Electronic assembly — reworking and touching up the coating with removal products

How do we supply Electrolube in Romania?

We can quote Electrolube protective coatings, casting and encapsulation resins, thermal pastes, gels and pads. For a correct quotation, send the application, the working temperature, the application method (spraying, immersion, dispensing or aerosol), the pack size wanted and the code of the product you use. Items are supplied to order; the lead time is usually 1–4 weeks, and for special pack sizes it may be longer.

The suitable product is confirmed in the quotation, after we review the application, the working temperature and the application method.

Frequently asked questions about Electrolube

What are UVFlex, DCA, ER2074 and PCG300 from Electrolube?

UVFlex is a UV-cured, single-component protective coating, and DCA is a modified alkyd coating. ER2074 is a flame-retardant, thermally conductive epoxy encapsulation resin, and PCG300 is a pre-cured thermal gel of 3.0 W/m·K.

How do I choose between a thermal paste with silicone and one without?

HTS and HTSP contain silicone, while HTC and HTCP are silicone-free, so the choice depends on whether silicone is permitted in the application. HTCP is suitable where silicones are prohibited. Send the application, the conductivity wanted and the working temperature.

Do you supply Electrolube products in Romania, and how quickly?

Yes. Electrolube coatings, resins and pastes are supplied to order, with a usual lead time of 1–4 weeks, and a product can ship in 24–72 h when the item is in stock, locally or at the supplier. For special pack sizes the lead time may be longer; the quotation confirms it.

Can I replace the coating or resin that I use?

Yes, if the chemistry, the working temperature and the application method match. Send the name of the current product, the technical data sheet if you have one, and the application, and we check which Electrolube product comes closest to the requirements.

What details do I send for a quotation on a coating, a resin or a thermal paste?

Send the application (board, module or LED), the working temperature, the application method, for example spraying, immersion, dispensing or aerosol, and the pack size wanted. For a paste, add the thermal conductivity required, and for a resin, whether UL94 V-0 flame retardance is needed.

How do I request a Electrolube quotation?

Send the Electrolube code from the nameplate and the quantity; we reply in English with availability and the lead time written in the quotation.

Request a quote

Updated: 21 November 2026 · Sources: Electrolube (manufacturer documentation)