Skip to content
+40 371 232 404|Mon - Fri: 08:00 - 16:30 (Romania time)

Senseair supplier in Romania

For Senseair we quote NDIR CO₂ sensors Sunrise, Sunlight, S8, S88 and S88 GH, as well as modules for refrigerants Sunlight R290 and RDS R290; we need the gas, the range, the interface and the power supply.

Headquarters: Delsbo, Sweden

Request a quote

Who is Senseair and what does it make?

Senseair is a Swedish manufacturer headquartered in Delsbo, making gas sensors with NDIR (non-dispersive infrared) technology, which it has used for more than 30 years. An NDIR sensor measures how much of the infrared light is absorbed by the gas, so it consumes no reagent and is not poisoned, unlike other measuring principles. The ABC function (automatic baseline correction) brings the zero back to the minimum value measured in a given interval, so that the sensors can work for years without recalibration. For an air-conditioning or automation engineer, what matters is a small, individually calibrated module that mounts directly on the product board.

The carbon dioxide range starts with Sunrise (0–10,000 ppm, ±30 ppm ±3 % of the reading, with an LED as the light source) and Sunlight CO₂, designed for battery-powered or wireless use. S8 (400–10,000 ppm, ±40 ppm ±3 %, UART interface, estimated service life of over 15 years) is used in air-conditioning equipment, and S88 renews it with the same form and the same pins, in line with ANSI/ASHRAE 62.1-2022. S88 GH covers 0–20,000 ppm and humidity 0–95 % for greenhouses, S12 has a micro format, S8 5 % and 2 % serve alarms (0.04–5 % by volume), and the K series goes up to 30 %. For refrigerants there are Sunlight R290 and Sunlight R32 and R454 A/B/C, as well as the RDS housings with IP66 and IP67 protection, internal heating and Modbus, with a range of 0–100 % LFL (lower flammability limit).

The applications are ventilation controlled by CO₂ level, indoor air quality monitoring, greenhouses, concentration alarms and heat pumps with propane refrigerant. The quotation starts from the module code and the interface used (UART, Modbus, I2C) for replacements, or from the range and power supply for new projects.

What do we supply from the Senseair range?

ProductDescription
Sunrise and Sunlight CO₂NDIR CO₂ sensors with LED, 0–10,000 ppm. Sunrise has an accuracy of ±30 ppm ±3 % and also exists in a Dual Technology version for permanently occupied spaces; Sunlight has very low power consumption, suitable for batteries or wireless power, and complies with ANSI/ASHRAE 62.1-2022.
S8, S88, S88 GH and S12S8 and S88 measure 400–10,000 ppm, are individually calibrated and have UART, the S88 renewing the S8 with the same pin layout. S88 GH is for greenhouses, 0–20,000 ppm and humidity up to 95 %, and S12 is the micro-format version for tight spaces.
S8 5 % and 2 %, K seriesS8 5 % and 2 % measure CO₂ in the range 0.04–5 % by volume, for alarms, for example leak detection. The K series, with flexible optics, goes up to 0–30 %, in housed or board-mounted versions, for high-concentration applications.
Sunlight R290, R32 and R454, RDSNDIR modules for refrigerants: R290 (propane, class A3), R32 and R454 A/B/C. Sunlight is the module, RDS is a system in an IP66 or IP67 housing, with internal heating for cold conditions, Modbus and digital output, range 0–100 % LFL, accuracy ±2.5 % LFL.

Why Senseair?

  • Solid-state NDIR — no reagent consumption and no poisoning, with automatic baseline correction (ABC) for long-term operation
  • Several power consumption levels — Sunlight for battery or wireless use, Sunrise for accuracy, S8 and S88 for volume integration on boards
  • Same pin layout on the S88 — keeps the form and pins of the S8 series and complies with ANSI/ASHRAE 62.1-2022
  • Sensor for greenhouses — S88 GH measures 0–20,000 ppm at humidity of up to 95 %, with several output types
  • Refrigerant detection — Sunlight R290 and R32 and the RDS housings in IP66 and IP67, with internal heating and Modbus

Which Senseair codes and series are requested most often?

CodeDescription
SunriseNDIR CO₂ sensor, 0–10,000 ppm
Sunlight CO₂NDIR CO₂ sensor with very low power consumption
S8NDIR CO₂ sensor, 400–10,000 ppm, UART
S88Renewal of the S8 series, same pin layout
S88 GHCO₂ sensor for greenhouses, 0–20,000 ppm
S12 CO₂NDIR CO₂ sensor in micro format
S8 5 %CO₂ sensor for alarms, 0.04–5 % by volume
S8 2 %CO₂ sensor for alarms
K-seriesCO₂ sensors with flexible optics, up to 30 %
Sunlight R290NDIR module for propane R290 detection
Sunlight R32 / R454 A/B/CNDIR module for refrigerants R32 and R454
RDS R290R290 refrigerant detection system in IP66/IP67 housing
RDS R32 / R454 A/B/CHoused detection system for R32 and R454

Where is Senseair equipment used?

  • Air conditioning and ventilation — ventilation controlled by the CO₂ level in buildings
  • Indoor agriculture — CO₂ control in greenhouses and vertical farms
  • Heat pumps and refrigeration — leak detection for refrigerants R290, R32 and R454
  • Air quality monitoring — battery-powered or wireless products
  • Concentration alarms — CO₂ measurements in ranges of a few percent

How do we supply Senseair in Romania?

We can quote Senseair sensors from the Sunrise, Sunlight, S8, S88, S88 GH, S12 and K series and the modules for refrigerants Sunlight R290 and RDS. We supply to order, usually in 1–4 weeks, and depending on the specification the lead time can be longer for large quantities or custom versions. For a correct quotation, send us the code or series of the existing sensor, the gas and the range to be measured, the supply voltage, the interface (UART, Modbus, I2C or analogue) and the operating temperature. For a new product, add the available mounting space.

The compatibility of a module with an existing board is established by comparing the pins, the interface and the power supply.

Frequently asked questions about Senseair

What does Senseair make?

Senseair makes gas sensors with NDIR technology: CO₂ sensors for buildings, greenhouses and alarms, as well as modules for detecting refrigerants R290, R32 and R454. The company works from Delsbo, in Sweden, and has more than 30 years of experience in NDIR.

How do I choose between Sunrise, Sunlight and S88?

Sunrise is chosen when accuracy matters (±30 ppm ±3 %), Sunlight when the power supply is a battery or wireless, and S88 when a module with the pin layout of the S8 series is integrated into series products. Send us the power supply, the interface and the desired range, and we propose the series.

Can Senseair sensors be supplied in Romania, and how quickly?

The sensors are supplied to order, usually in 1–4 weeks. A model can ship in 24–72 h when the item is in stock, locally or at the supplier. For large quantities or custom versions, depending on the specification, the lead time can be longer; we set it in the quotation.

Can an S8 sensor be replaced with an S88?

The S88 is a renewal of the S8 series, with the same format and the same pins, but compatibility is checked on the specific version: range, interface and power supply. Send us the code from the sensor and the board diagram, and we check what is kept without design changes.

What data should I send for a quotation on a gas sensor?

Send the gas and the range to be measured, the required accuracy, the supply voltage, the interface (UART, Modbus, I2C, analogue), the operating temperature and humidity and the number of pieces. For refrigerants, add the refrigerant type and whether an IP66 or IP67 housing is needed.

How do I request a Senseair quotation?

Send the Senseair code from the nameplate and the quantity; we reply in English with availability and the lead time written in the quotation.

Request a quote

Updated: 21 November 2026 · Sources: Senseair AB (manufacturer documentation)