Sintrol supplier in Romania
Dust monitors for stacks, filters and processes, inductive electrification
Headquarters: Helsinki, Finland
Who is Sintrol and what does it make?
Sintrol Oy is a Finnish company from Helsinki, with more than five decades of activity in industrial measurement, best known for dust monitors and dust monitoring systems. For customers in Finland the company also does process analysis, automation, combustion control and non-destructive testing; for export, however, the range is concentrated on dust: emission monitors for stacks, filter and process monitors, monitors for dust in workspaces, and software for configuration and data archiving.
The basic technology is inductive electrification, in which an insulated probe records the charge produced by particles and converts it into a signal proportional to the dust concentration. From it derive the S100 series (S101 with two relays, S103 with isolated 4–20 mA output), suited to detecting broken bags in ducts up to 800 mm, then S304 calibratable in mg/m³, S305QAL, with measurement approvals stated in the manufacturer's documentation, for official emissions in waste combustion and in large combustion plants, and S314 in a separate architecture, with the sensor unit at the measuring point and the electronics up to 500 m away. For wet gases that condense, EXO QAL is an extractive system with a sample heated above the water and acid dew point.
For Romania, the range is relevant for bag filters, power plants, cement, flour and sugar mills, timber, mines and other installations in which dust is both an emissions problem and an explosion safety problem. For a quotation, what matters is the duct diameter, the temperature, the gas humidity, the Ex zone and whether QAL1 certification is required.
What do we supply from the Sintrol range?
| Product | Description |
|---|---|
| S100 / S101 / S103 Ex | Filter monitors for detecting broken bags and dust variations, in ducts up to 800 mm, with IP66 housing and variants for explosion-risk zones. S101 has two relays, S103 a 4–20 mA output. |
| S304 / S304QAL | Continuous dust monitors, calibratable in mg/m³, with 4–20 mA output and two alarm relays. The variants S304QAL-L and -D, for filter leaks and dust after the filter respectively, have measurement approvals stated in the manufacturer's documentation. |
| S305QAL and S314 | S305QAL is the monitor for official emissions, with measurement approvals indicated in the manufacturer's documentation. S314 and S314 Ex separate the sensor unit from the connection unit, with cables up to 500 m, for hard-to-reach measuring points. |
| EXO QAL, E-SPY, DumoPro | EXO QAL for dust in wet gases, E-SPY for the dust trend after electrostatic precipitators, DumoPro for dust in production halls, with DustTool and DustCloud software. |
Why Sintrol?
- Inductive electrification — the technology stays sensitive to dust even if the probe is partly fouled, with low temperature drift and no consumables
- Auto Setup — the monitor adapts its own measuring range and alarms under normal process conditions
- S305QAL for combustion and waste incineration plants, with measurement approvals according to the manufacturer's documentation
- S101 / S103 commissioning in about 500 seconds — after mechanical and electrical installation, the stated time is about 8 minutes
- EXO QAL for wet gases — sample heated above the dew point, with automatic probe cleaning, where in-situ monitors do not work
Which Sintrol codes and series are requested most often?
| Code | Description |
|---|---|
| S101 | Filter monitor, two relays |
| S103 | Filter monitor, isolated 4–20 mA output |
| S201 | Dust monitor for filtration and process |
| S203 | Dust monitor for filtration and process |
| S303 | Dust monitor for filtration and process |
| S304 | Continuous dust monitor, calibratable in mg/m³ |
| S304QAL-L | Monitor for filter leaks |
| S304QAL-D | Dust monitor after the filter |
| S305QAL | Emission monitor |
| S314 | Dust monitor with separate architecture |
| S314 Ex | Variant for explosion-hazard zones |
| EXO QAL | Extractive dust monitor for wet gases |
| E-SPY | Dust trend monitor after electrostatic precipitators |
| DumoPro | Dust monitor for industrial spaces |
| DustTool | Configuration software |
| DustCloud | Software for archiving and viewing data |
Where is Sintrol equipment used?
- Power plants and incineration — dust emissions in the stack
- Cement, steel and chemicals — bag filters and electrostatic precipitators
- Flour, sugar and grain mills — dust in workspaces, explosion risk
- Timber industry and mines — filters and halls
- Purification and paper — wet process gases, scrubbers
How do we supply Sintrol in Romania?
We can quote Sintrol dust monitors, from broken bag detectors to emission monitors. The equipment is supplied to order; usually 1–4 weeks, while variants for explosion-risk zones or with approvals stated in the manufacturer's documentation, as well as extractive systems for wet gases, can have a longer lead time, set in the quotation. To identify the model, we need the duct diameter, the gas temperature and humidity, the type of dust, the concentration range, the Ex zone and the certification requirement. For replacements, send the monitor code (for example S303 or S304) and the probe length.
Compliance with a specific environmental permit is established after analysing the conditions of the installation, and calibration in mg/m³ is based on gravimetric measurements made on site.
Frequently asked questions about Sintrol
What products does Sintrol make?
Sintrol is a Finnish company from Helsinki, known for dust monitors based on inductive electrification: broken bag detectors (S100), process monitors (S3xx), the S305QAL monitor for emissions, EXO QAL for wet gases, E-SPY for electrostatic precipitators and DumoPro for workspaces.
How do I choose between an S101 and an S103?
Both detect broken bags and dust variations in ducts up to 800 mm. S101 has two alarm relays, S103 has an isolated 4–20 mA output for sending the value to the control system. If you have an Ex zone, there are the S101 Ex and S103 Ex versions, with IECEx and ATEX variants according to the manufacturer's documentation.
Do you supply Sintrol monitors in Romania, and how quickly?
Yes, the monitors are supplied to order, usually in 1–4 weeks. Monitors with measurement approvals according to the manufacturer's documentation, variants for explosion-risk zones and EXO QAL extractive systems can have a longer lead time, which we specify in the quotation, after the installation is clarified.
Can I replace an older Sintrol monitor with a current model?
The S100 series is the updated version of the former Snifter series. For confirmation, we need the monitor type, the probe length, the supply voltage and the outputs used, plus a photo of the nameplate. We confirm compatibility on the basis of these data.
What data do I need to send for a quotation on a dust emission monitor?
The diameter of the stack or duct, the gas temperature and humidity, the fuel or process, the concentration range, whether QAL1 to EN 15267-3 is required, the Ex zone and the output type. For calibration in mg/m³, reference gravimetric measurements are also planned.
How do I request a Sintrol quotation?
Send the Sintrol code from the nameplate and the quantity; we reply in English with availability and the lead time written in the quotation.
Request a quoteUpdated: 21 November 2026 · Sources: Sintrol Oy (manufacturer documentation)

