Skip to content
+40 371 232 404|Mon - Fri: 08:00 - 16:30 (Romania time)

Pomona Electronics supplier in Romania

test leads and probes, RF connectors, accessories for multimeters and oscilloscopes

Founded in 1951 · Headquarters: Everett, Washington, USA

Request a quote

Who is Pomona Electronics and what does it make?

Pomona Electronics is an American manufacturer of electrical test and measurement accessories, based in Everett, Washington, USA. The range covers test leads and probes for multimeters, grabber-type clips for SMD test points, RF/coaxial connectors and adapters, test cords and static control accessories. For the Romanian market we can quote accessories from these families, useful wherever routine electrical measurements are made in the laboratory or at the workbench.

What sets the Pomona range apart is the variety of grabber and micrograbber clips for hard-to-reach test points, from standard clips for wires to micro-SMD versions for terminals of only 0.3–0.8 mm, available in sets of up to ten colours for quick circuit identification. The RF/coaxial connectors and adapters cover several connector families, confirmed by code. Telecom and low-frequency cables complete the range for permanent or temporary test setups.

In Romania, the Pomona range makes sense for metrology laboratories, electronic service workshops and maintenance teams that constantly need spare test leads, clips and adapters, without depending on a separate supplier for each small accessory.

What do we supply from the Pomona Electronics range?

ProductDescription
Grabber and Micrograbber Test ClipsA broad family of clips for quick connection to test points, from Minigrabber for wires a few millimetres in diameter, to Micrograbber for small terminals, up to Micro SMD Grabber for ICs of 0.3–0.8 mm, available in ten-colour sets for identifying circuits in multichannel measurements.
Test Leads and Probes for MultimetersSets of test leads with shrouded banana plugs and interchangeable tips, plus medium and industrial size alligator clips for firm connection to terminals and bus bars, useful both for general bench use and where a stable contact is needed over a longer period.
RF/Coaxial Connectors and AdaptersCoaxial and RF adapters for interconnecting test equipment with different impedances and connectors, in several connector families, plus kits for changing the connector type (confirmed by code), useful for connecting spectrum analysers to the device under test.
Test Cords and Static Control AccessoriesTest cords with banana plug, alligator clip or pin, plus banana jacks and binding posts for permanent panel installations, along with static control accessories, useful in areas where ESD-sensitive components must be protected during handling.

Why Pomona Electronics?

  • Grabber and micrograbber clips in dozens of versions, from standard wires to SMD terminals of under a millimetre.
  • RF/coaxial connectors and adapters for interconnecting test equipment, with the connector family confirmed by code.
  • Accessories available in colour sets, useful for quick circuit identification in multichannel measurements.
  • A broad catalogue of test accessories, with codes and dimensions specified for each product.

Which Pomona Electronics codes and series are requested most often?

CodeDescription
3925Minigrabber clip for thin wires, ten colours available
4176Minigrabber clip kit, one black and one red clip
4233Do-it-yourself Micrograbber clip for small terminals
4521Micrograbber clip with square pin, black or red
4555Minigrabber clip for thicker wires, ten colours
4723Minigrabber clip with integrated banana plug
4826Minigrabber clip with tip plug, black or red
5243SMD Grabber clip, available in ten colours
5360SMD Grabber clip with 0.025 in (0.64 mm) square pin, ten colours
5418Do-it-yourself Minipincer clip, ten colours available
5520SMD Grabber clip kit, complete ten-colour set
5522Minigrabber clip kit, complete ten-colour set
5790Rotating Micrograbber clip with two square pins
5830Maxigrabber clip with banana plug and screw for direct wire
6351Micro SMD Grabber clip for 0.3–0.5 mm ICs, set of 10
6352Long-tip Micro SMD Grabber clip, for 0.5–0.8 mm ICs
6353Micro SMD Grabber clip for 0.5–0.8 mm ICs, set of 10
6442Short-tip Micro SMD Grabber clip, set of 2
72902Micro SMD Grabber clip kit with support rods
72906Mini SMD Grabber clip set for dense test points

Where is Pomona Electronics equipment used?

  • Metrology laboratories: spare leads and probes for reference multimeters and oscilloscopes
  • Electronic service: micro-SMD clips for troubleshooting boards with dense components
  • Electronics production: static control accessories for handling ESD-sensitive components
  • Telecommunications: RF/coaxial connectors and adapters for test benches
  • Technical education: sets of colour-coded leads and clips for teaching laboratories

How do we supply Pomona Electronics in Romania?

We can quote Pomona accessories from the families of grabber clips, test leads and RF connectors, to order. The range is supplied to order; we work from the manufacturer's technical documentation to confirm the exact codes and dimensions before sending the quotation. For a specific accessory, it is enough to send us the model number from the old part or a description of the application (which multimeter or oscilloscope you use, which type of test point you need to reach), and we confirm compatibility and the lead time (to order, usually 1–4 weeks) before the order is placed. Availability is checked for each catalogue code.

Availability of older or discontinued codes in the Pomona catalogue is checked code by code.

Frequently asked questions about Pomona Electronics

What products does Pomona Electronics make?

Pomona Electronics makes electrical test and measurement accessories: test leads and probes for multimeters, grabber-type clips for SMD test points, and RF/coaxial connectors and adapters. The company is based in Everett, Washington, USA.

How do I choose the right Pomona clip for an SMD test point?

The choice depends on the terminal size: Micro SMD Grabber clips cover ICs of 0.3–0.8 mm, while the standard SMD Grabber versions suit larger points. Send us the terminal size and the type of measurement so we can confirm the right code.

Can you supply Pomona Electronics accessories in Romania, and within what time?

Yes, to order, usually in 1–4 weeks depending on the manufacturer's confirmation. The range is supplied to order for each catalogue code, so the exact lead time is confirmed before the order is finalised.

What details should I give for a test accessories quotation?

The model code if you know it, or a description of the application: which multimeter or oscilloscope you use, the type of test point and the wire diameter. We check compatibility in the manufacturer's technical documentation and confirm the exact code before sending the quotation.

How do I request a Pomona Electronics quotation?

Send the Pomona Electronics code from the nameplate and the quantity; we reply in English with availability and the lead time written in the quotation.

Request a quote

Updated: 21 November 2026 · Sources: Pomona Electronics, Wikipedia (manufacturer documentation)