Skip to content
+40 371 232 404|Mon - Fri: 08:00 - 16:30 (Romania time)

Shock Absorbers, Vibration Isolators and Gas Springs

Industrial shock absorbers stop a moving mass over a short distance, converting kinetic energy into heat; gas springs provide a controlled force for lifting or balancing covers and doors, and elastomer or steel vibration isolators separate a machine from the structure it stands on. All of them protect the equipment, the structure and the operator from shocks and vibration, and the choice starts from mass, speed, frequency and environmental conditions.

An industrial shock absorber absorbs the energy of a mass coming to a stop at the end of its stroke. The self-adjusting hydraulic versions use throttling orifices distributed along the stroke, so the braking force stays almost constant throughout, stopping the mass smoothly. The adjustable ones allow tuning for mass and speed, while the simpler elastomer or polyurethane elements tolerate only small energies. The gas spring uses pressurised nitrogen in a cylinder with a rod and gives a relatively constant force over the stroke, with less variation than a mechanical spring.

Vibration isolators are chosen by the excitation frequency of the machine and the natural frequency of the isolated assembly. The basic principle: isolation occurs only when the excitation frequency is clearly higher than the natural frequency; otherwise the assembly may amplify the vibration instead of reducing it. Elastomer damps well and is compact, the steel spring carries large loads and deflections, and the air spring offers a very low natural frequency. Load, speed and environment data decide the suitable type.

How to choose

Mass and impact speed

The kinetic energy to be absorbed at each stop is calculated from mass and speed; the shock absorber must be chosen for the real energy, with a margin, not just for the weight of the machine.

Energy per stroke and per hour

Besides the energy of a single stop, the number of cycles per hour matters, because the shock absorber heats up; at high frequencies, thermal capacity becomes the real limit.

Stroke and reaction force

A longer stroke gives a lower braking force for the same energy; check that the structure can take the reaction and that there is space for the stroke required.

Type of damping

Self-adjusting for variable loads, adjustable for known and stable conditions, simple elastomer for small energies.

Disturbing frequency and natural frequency

For isolators, the ratio between the two frequencies determines efficiency; an isolator that is too stiff transmits the vibration, one that is too soft makes the machine unstable.

Static load and weight distribution

Each support point takes part of the mass; calculate the load on each isolator taking the centre of gravity into account, so that all of them work within their load range.

Working environment

Temperature, oil, ozone and moisture affect elastomers and seals; choose a compatible material, and for gas springs respect the specified mounting position.

What to send for a quotation

  • The moving mass and its speed at the moment of impact
  • Number of cycles per hour and driving force, if any
  • Available stroke and mounting dimensions
  • For isolators: machine mass, working frequency, number of support points
  • Environmental conditions and working temperature
  • For gas springs: required force and stroke length

Typical applications

  • Overhead cranes and conveyors
  • Presses, hammers and injection moulding machines
  • Compressors, fans and pumps
  • Covers, doors and access panels of machinery

Maintenance and spare parts

Shock absorbers are checked visually at regular intervals for oil leaks, rod deformation and the condition of the rod seal; a leaking shock absorber no longer stops the load correctly and must be replaced. Elastomer isolators are inspected for cracks, hardening and settling, and gas springs are replaced in pairs when the force drops. Do not open or heat a gas spring, because the cylinder is under pressure.

Brands we quote for this product type

Frequently asked questions

How do I calculate whether a shock absorber can stop my load?

Calculate the kinetic energy of the moving mass and, if there is one, add the work done by the driving force over the stroke of the shock absorber. The result is compared with the maximum energy per stroke and the energy per hour of the shock absorber. If the number of cycles is high, thermal capacity also matters. An undersized shock absorber quickly reaches the end of its stroke and passes the shock on to the structure, while an oversized one may stop the mass too abruptly.

What is the difference between a shock absorber and a gas spring?

The shock absorber stops a mass at the end of its movement, converting the energy into heat without returning it. The gas spring gives a relatively constant force over the stroke and helps lift or balance a weight; it can also have end-of-stroke damping. They are elements with different roles and cannot replace each other. Describe the movement and the force required for the correct recommendation.

What data do I provide for a quotation, and how soon is it delivered?

Send the mass, speed, cycles per hour, available stroke, mounting dimensions and environmental conditions; for isolators, the machine mass, working frequency and number of support points. If you are replacing a part, the code on the body is enough. Delivery is 24–72 h when the item is in stock, locally or at the supplier, while made-to-order items usually take 1–4 weeks; it can take longer depending on brand and specifications.

Why does the machine vibrate more after the isolators were fitted?

The typical cause is an isolator whose natural frequency is close to the excitation frequency of the machine, in which case resonance occurs and the vibration is amplified. It may also be a load on the isolator outside its range, or an uneven weight distribution. Check the frequency ratio and the real load on each support point, then choose isolators with a natural frequency clearly lower than the excitation frequency.

Updated: 2026-11-20